forum.heinrichsweikamp.com

Yep, that´s it, #1 is always default.
From sleep-mode it will always resume with the default #1 setpoint.

I have my three setpoints set to 1,0 / 1,2 and 1,4 PO2, default is 1,2.
Whatever setpoint i choose when diving it will remain the same thruout the dive.
Only when the OSTC switches off and then on again it automatically switches to the default setting 1,2.

My OSTC's are not doing any automatic PPO2 switching.
I'm still using 1.29 and 1.30

OSTCfan Wrote: ------------------------------------------------------- > Bit concerend here too as it seems a lot of > attention has gone to the OC side of the computer, > but the CCR side is possibly a bit dodgy. > > Can we have some extensive (or at least some more > attention given to) the CCR si...

Hello,

what i understood sofar is that the bug with increasing TTS is only active for the first dive after upgrading.
All subsequent dives are eventless.
This is at least the case for my two units and i believe some other users mentioned the same.
Also i'm quite happy with the CCR-features.

Reiner

Hi,

i tried the same thing with a Yahoo Group but there was no interest at all.
Maybe the community is still to small.
Anyhow, good luck.

Reiner

Hallo, fuer mich persoenlich ist eine Abweichung von ca. 1% nicht wirklich der Rede wert. Das Thema wuerde hier auch schon diskutiert, kannst ja mal die Suchfunktion bemuehen. Es kommt auch darauf an ob die anderen Computer auf Salz- oder Suess-Wasser geeicht sind. Um sich wirklich ein Bild machen z...

Hi Chris, just saw your post now. There's three surface-preset PO2 settings available to choose from. I'm using my OSTC as a back-up for my Vision and i always leave it on 1.3 PO2 thruout the dive as the tissue-load during descent on 0.7 is so marginal it barly influences the total load and TTS by l...

corona_citron Wrote:
-------------------------------------------------------
> oh sorry, I didn't mentioned the solution....
> I though it was evident


No, it is not.
Let us know.

Hi,

i guess everybody here is very much interested how to solve this kind of problem.
I believe this was solved remotely?
So please tell us a little bit about it, that's what a forum is for.

Thanks, Reiner

Hi,

i got it now with the latest divinglog software and OSTC add-on as mentioned.
Obviously i was using an older divinglog version on this PC.

Thanks a lot, Reiner

can't find it.

Ah, ok, i changed only CF0 but i'll have to change CF6 to 1150 for a 2 meter deep pool, thanks.

Hi,

same same hung-up when selecting O2 Mon. in the UW-menue again, snapshot before resetting send by Email.

Another thing is my OSTC's wount start automatically in a 2 meter deep pool even after adjusting CF0 to 50 cm. I have to start them manually.

Reiner

Hi Matthias,

Firmware ID:

SN 186: 011DCE6EE97DA95475FD91A52F4CBD9481F7
SN 36: 011DCE6EE97DA95475FD91A52F4CBD9481F7

So both the same.

Is it this what you where asking for?

I will check the bug for you again right away.

Thanks, Reiner

Hello,

i did it before but i can't figure out how to do it anymore.

How can you write or edit a note ( e.g. your name ) in the bottom row on the surface display.

I know i did it with the interface but i can't find the option anymore.

Thanks, Reiner

Hi, i did a dive today with software 1.29 to 72 meters, bottom time 20 minutes, total time 85 minutes, on CCR with diluent 14/50 and GF 5/90. Everything was fine during the dive and the deco was very close to my shearwater and vision as usual. No bug, no hung-up, no funny deco-info or so, very smoot...

Hi,
i`m using GF 5/85 to make my profile as close as possible to my budies VR3 and like this my OSTC calculates much deeper deepstops, of course depending the profile and gas used.
My DS`s are still not as deep as the VR3 DS`s but they come much closer compared to GF 30/85.

I'm also interested to know if it is possible to run the O2-board with one cell only?

Hi Holger, i'm very interested. I'ld like to use my existing tecme-sensorholder so i need a 7-pin Fisher female socket connector on the housing for the input from the tecme holder and a 5-pin Fisher male wire to connect the housing to the OSTC. How about the HUD itself. Are you also going to offer a...

Hallo, ich schlage vor eine Email-Liste fuer interessierte Nutzer zu gruenden um vor Allem ueber fehlerhafte Stable-Software-Versionen zu informieren und evtl. auch ueber neue Stable-Software-Versionen. Ich bin erst jetzt darauf aufmerksam geworden das die Version 1.28 wiederrufen wuerde und auf kei...

Hallo,
ich sehe das genauso.
Bei der neuen Matrix blenden die LEDs richtig durch die transparenten Zeichen.
Die alte Matrix hat mir auch besser gefallen.
Gruss, Reiner

Hi,

try GF 30/90 which is the most agressive setting without displaying the death skull.
This should give you some more NDL but i'm not sure if it will give you 12 min. on 33 mtr.

Reiner

P.S.: 15/85 will give you less NDL then 30/85.

Hello, i just post a reply from Matthias in another thread: heinrichsweikamp Wrote: ------------------------------------------------------- > Hello, > > An eCCR use with the OSTC is currently not > supported and due to liability reasons not on our > to-do list, sorry. > > A technically skilled perso...

Hi,
i'm sure it is possible to use the OSTC with the O2-board as an O2-analyzer as already mentioned.
But i'm also sure there's no chance to use the OSTC as a Helium-analyzer.
Reiner