forum.heinrichsweikamp.com

Hello Robert,

"12-xxx" is one of the latest batch, it's fine.

Yes, there are several projects we're in contact with. As soon as any is ready we'll publish is here. We are also thinking of an alternative right now.

regards,
Matthias

Hello, Check the wiki: http://www.heinrichsweikamp.net/ostc/pmwiki/pmwiki.php?n=Manual.Interface There is step by step manual. It's essential that the update works, seems that you did not install the driver already. If possible, please try to give more detailed informations about your system/error m...

Hello Robert.

Update to 1.28 and you'll find this entry.

http://www.heinrichsweikamp.net/ostc/en ... CCDB62.htm

Regards,
Matthias

Hallo, Das Verhalten ist zwar nicht direkt ein Bug aber das haben wir schon auf der To-Do Liste. Hintergrund ist, das der Simulator relativ einfach implementiert ist, an der Schnittstelle eingehende Bytes werden im Simulatormodus als Tiefenangabe interpretiert. Das von Divinglog (korrekterweise) ges...

Hello,

An eCCR use with the OSTC is currently not supported and due to liability reasons not on our to-do list, sorry.

A technically skilled person could attach a solenoid driver to the O2 monitor board. Firmware of the board is Open Source, too...

Regards,
Matthias

Hello,

No, all HUD-related settings are only set by the OSTC (The settings are stored in the board permanently and transferred from the OSTC in the O2 Sensor Setup menu).

Cheers,
Matthias

Hello,

If you once have installed the O2 board, please post some pictures of you setup. This is always interesting to other users.

Regards,
Matthias

Hello, It a bit more complex: When using high efficiency LEDs with additional series resistors it's fine with OSTC powered operation but the start-up delay can be about 20 seconds for the board (Then it's important to activate the OSTC before the dive manually). When using normal LEDs or no extra se...

Technically, the O2 board can be connected to both versions of the OSTC easily but if you consider the costs for the board, Fischer connector and the O2 cell a dedicated O2 meter is probably cheaper.

Regards,
Matthias

This is a 0.2F capacitor buffering intermittent power supplies: http://www.panasonic.com/industrial/com ... 00CE19.pdf

Regards,
Matthias

No worries about a battery, there is no battery on the O2 board even if some parts look like that.

Christian

Hello,

The new 2.10 JDivelog is now available on http://www.jdivelog.org It supports the newer OSTC functions introduced in the last beta versions.

Regards,
Matthias

Hello Alain,

Please contact us directly, I'm sure we get this working again: info@heinrichsweikamp.com

Regards,
Matthias

Hello, After resetting the OSTC (With the interface) it will re-read the calibration from the sensor and you should see fine readings. Can't tell what you did but you can not damage the unit with a simulation. Also try a "reset all" from the interface and/or install the 1.26 beta version. ...

Und das bleibt nat?rlich in den n?chsten Versionen so erhalten.

Gruss,
Matthias

Hello, Thanks for your post! We have tested the bootloader on different VISTA systems (Home and Prof.) and it worked. Maybe the wrong driver was installed? We tried the non-beta 2.04.06 from FTDI and it connected with 19200. The non-customized, original "Tiny bootloader" works fine, too. R...

Hello, I must admit that we underestimated the amount of diver without sufficient correction masks. Next step on our display-to-do-list is a new middle-sized font with more simple, clear figures. I'm afraid the small font will not be changed in the future but we can try to move more important inform...

Hi,

Since we do not draw much current from the battery (only 1/10 of the specified max. current) I do not expect a significant drop of ON-time with a fully charged battery. Make sure the unit is stored in warm conditions (Do not leave it in the car overnight, for example!).

regards,
Matthias

servan Wrote: > No. Does the yellow led blinking when I try to > reset ? Or always ? If the battery voltage is critical (caused by whatever) the battery is hard-disconnected from the OSTC (To avoid battery under-discharging) and will reconnect after the interface is attached and the reset button is ...

Hello,

Which firmware do you use, is the Interface Power-LED on? Maybe the yellow LED is blinking some kind of error code?

regards,
Matthias

It's correct that the NDL time calculation is based on the selected gas only. But as soon as deco is displayed deco gases are included in the calculation, no matter which gas# they have. I have tested this again and again today with different combinations. A new 1.27 will be available soon, with sev...

Hello, That's the No Deco Limit (NDL) and it's starting at 160 because it's programmed to do so. You'll see a NDL time in any other computer doing deco calculations. While the NDL can be higher then 160minutes the OSTC stops calculations for NDL>160minutes (Very shallow waters). Other computers disp...

I have simulated some dives just yesterday and it worked as it should. Maybe you start with gas1 and set the deco gas to gas2 (That's what I did). Maybe there is still a bug in the decogas routine. I doubt that this is related to a hardware problem.

Regards,
Matthias

Hallo,

Da gibt es noch keinen definitiven Termin. Du kannst aber auch die Beta mal testweise installieren, ein "Downgrade" ist danach problemlos m?glich.

Viele Gr?sse,
Matthias

If I simulate two different dives, 15min at 65m on 21/0 a) with O2 Deco at 6m b) with Air Deco I clearly see the difference of about 16minutes deco time at the end of the bottom time. Make sure gases are configured as active and change-depths are fine. Disable any other gases. I use "ZH-L16 OC&...