forum.heinrichsweikamp.com

Hello Kurt,

It's on our long-term plan from the beginning. We had some discussion on this on the last "boot" show in D?sseldorf. Still legal and technical problems to solve...

Regards,
Matthias

> 2. Active Gases > Example I do a dive to 40m with active Gases Air > (0m), EAN50 (21m) and O2 (6m). > Does the OSTC automatically calculate the > decompression time based on this 3 gases? The OSTC forecats deco sum based on the the active gases and presumes 10/min ascend speed. > What will happen ...

andersnasman Wrote: > 1. Yes I find the Calibrate x %O2, where do I set > what PO2 to calibrate to? That's your Diluent or "Start Gas" in Menu -> Gas Setup > 2. The setup #37 states HUD style [0-3] but there > is three possible values, which is 0,1,2? I guess > 3 is not valid? 0=OSTC 1=DS1...

Hallo,

Das ist absichtlich so eingebaut, damit neu hinzugef?gte CFs auch wirklich einen sinnvollen-Default Wert bekommen. M?ssten wir vielleicht mal etwas intelligenter machen damit alte Werte nicht ?berschrieben werden....

Gruss,
Matthias

Hello,

When not in simulation mode, the unit will not listen to the interface, of course.

Matthias

Hello,

No, without looking at the screen you can not detect the mode of the OSTC.

We can ignore the command or (better) decrease the end-dive delay for simulations to 10sec. Repeated descents are usually nothing for simulation, they only occur in the real world

Cheers,
Matthias

So, 1.26 ist oben. Ich schreibe gleich noch was dazu...

Gruss,
Matthias

Here is a nice approach for dry sensors:

http://www.theadaptivesystem.com/electronics.html

regards,
Matthias

Hallo Andreas,

Wir warten sehns?chtig auf unsere komplett neue Homepage wo neue Firmwares dann deutlich komfortabler hochgeladen werden k?nnen. Dauert leider noch ein bisschen. Eine 1.26 gibt's aber demn?chst noch auf der alten Homepage. Wir sind noch am t?fteln...

Gruss,
Matthias

Hello Anders, See CF24: http://www.heinrichsweikamp.net/ostc/pmwiki/pmwiki.php?n=Manual.CF24 All three sensors are logged already. Divinglog and JDiveLog do not display these data yet but I'm sure they will implement it in the future. In OC mode, all gas changes are stored as well. The ppO2 value is...

Hello,

I'll include this into the Simulator Menu with one of the next versions. It's a bit tricky to simulate all active gases but we'll see if it's possible.

regards,
Matthias

Der OSTC verwendet das ZH-L16C Modell von Buehlmann. Die Dauer der GF Stops werden ohne Umschweife so berechnet, dass man stufenweise an der Gradientenlinie auftaucht ohne diese GF Linie zu ueberschreiten. Die Temperatur wird nicht beruecksichtigt da uns dazu keine wissenschaftlich fundierte Formel ...

Hello,

For simplicity we currently reset the CF when upgrading to a new firmware. This is to make sure all new CFs are initialized correctly.

Regards,
Matthias

Hallo J?rg, Ein Austausch-Geh?use f?r den OSTC ist momentan nicht geplant. Da das Ger?t nie als Tieftauch-Computer geplant wurde ist das mit dem aktuellen Geh?use nicht m?glich, mit ?l-F?llungen experimentieren wir gerade und haben daf?r auch einen Exsikkator angeschafft mit dem wir unter Vakuum arb...

Hello,

Position and orientation of the display is fixed due to the design, sorry. Theoretically it can be installed 180? but this would bend the display cable quite sharp.

Regards,
Matthias

Hello,

The update for the new HUD styles in the card is not yet done. When available, HEX and sources are published as usual, of course.

Regards,
Matthias

Hello, For all who can't wait until Monday when we upload the new beta to the firmware page. I have it attached to this post ;) F?r alle, die nicht bis Montag warten wollen und die Firmware 1.25 Beta schon mal testen wollen - ich habe sie unten angeh?ngt ;) Changes (From changelog.txt): New in 1.25:...

Hallo,

Das ist schon in Arbeit Die 1.25 wird alle Dekodaten nach der Simulation zur?cksetzten und die tats?chlichen Gewebedaten echter Tauchg?nge werden im Hintergrund weiter berechnet. Diese Option steht dann auch per PC zur Verf?gung.

Gruss,
Matthias

Hello, To sum it up, we have: - Interface is working (You can download dives) - OSTC is working - OSTC can be resetted (required for the bootloader) So this is probably some kind of a Vista issue. Maybe you need to run the bootloader in administrator mode? We've tested it on Vista and it worked just...

Hallo,

Mit den Standard-Einstellungen passen etwa 30 1-St?ndige TG mit Profil in den Speicher.

Viele Gr?sse,
Matthias

Have you downloaded the Bootloader from our page? Because with this version the baud rate setting is preconfigured to 19200. 115200 will not work. The not-blinking TX led indicates some problems with the COM port settings. I would suggest: -check Divinlog and Bootloader COM port (Must be the same, o...

Ok, very good idea since the actual time value is displayed, too.

Regards,
Matthias

Well, you should ask this the manufacturer. Most likely all components are pressure resistant. I do not expect any problems with the batteries, as well. If you punctuate a LiPloy battery very carefully it starts smoking immediately so I think any air inside the battery would be a bad idea.

Matthias

Hello, Thanks for your suggestions. Is there a picture showing these bars somewhere? It's technically no problem to implement some more icons/graphics into the OSTC screen. Personally, I want the OSTC outputs as clear as possible. 3m: 12' is very clear to me. A bigger font for the list is possible, ...

Hello,

Since I do not have seen the internals of an X1 until today I only see the informations on their webpage. Seems like they are using a gel (unsuitable with the OSTC buttons) instead of an Oil.

regards,
Matthias