forum.heinrichsweikamp.com

Used for two 40= metre dives last weekend. As with the previous beta, my shallow deco at 4 metres disappeared when there was still about 5 minutes left. That is, one moment I had 5 @ 4m to do, then it was clear. I was running 26% bottom gas, 59% deco gas.

Why?

Ralph, sounds great.

I think there is no need to add more than one minute to TTS for ascent from 5 metres. Sure, you should take more, but it just causes confusion when it is 5 minutes.

Ralph Okay, I have now worked out why it did not work correctly. In the gas setting for NX26, I did not have a MOD set (it was 0 m). When I Reset to MOD: 47 m and reran the simulator, it came out as it should, giving the deco taking into account the deco gas. Is this a bug or is it the way it should...

Ralph When I run 45 m for 18 mins I get very similar to what you posted earlier but no 12 m stop at all. 18 and 15 m are red which is 26%, rest are yellow which is 61%. If you run this using the "Start Simulator" option, it comes out as I noted in my previous post, that is, it shows TTS an...

Okay, I just ran simulator for a very close dive to the one I did. That is, 45 m for 5 minis then 46 m for 10 mins then ascend at 18 mins which is 16 mins on bottom like I did. At 18 m and 15 m stops, the simulation is very close to real dive. At the 15 m stop, the computer is showing last stop of 1...

Ralph, Thanks for your reply. Yes, your simulation is approximately what happened BUT the last stop was not 7 mins it cleared after 3 mins, that is, it went from 4 mins to 0 mins in one go. This was not the TTS. You can see that in the profile I loaded. The other questions are why the computer does ...

See profile below. Note that at end of deco showing 4 mins @ 4 metres and then nothing. Settings Bottom mix: NX26 Deco mix: NX 61 with change set for 13 m GF: 30/85 Sat/desat: 100% Last deco: 4 m Gas change: +1 before1.stop: +1 Note that first deco stop was 1 @ 9, not 1 @ 4 like it used to be. As I ...

Today I did a 46 metre dive. The computer still does not take deco gases into account when showing TTS till you actually swap over. Also, the deco time for last stop went from 4 mins @ 4 m to cleared in one go. Why?

I did another deep dive on the weekend, 45 metres for 20 minutes. As I suspected from the first deep dive I did on this new firmware, the computer now operates totally differently to before. 1 Before this firmware update, if you had a deco gas activated, then the indicated deco took into account tha...

I also had this happen on the only dive I used after 3.01. I double checked all settings were correct.

3m .. means you have a deco obligation but it should disappear as you surface. Surprised it shows when you are at 3m, I have only seen it when at 30m and after 0 No Deco changed to 3m ..

Ralph, I have only done one deep dive since the upgrade (and since then my computer has had a depth sensor fail and is on the way back to Germany), but it did NOT offer the change to 100% at 7 m like I programmed it too. In fact, I realised that the indicated deco did not take this into account. Onc...

Wanting to change From 1m/s to 5m/s is changing from 60 metres per minute to 300 metres per minute. The first is about 3 times the old recommended ascent rate and 6 times the current recommended rate, the second is almost 17 times the old recommended rate and 30 times the current one! This would be ...

You are right on all things.

Will be Subsurface.

Thanks Matthias

Is the time when compass showing meant to be min:1/6 min?

aGF Value in that screen does not fully show high value.

Other than the above, looks fantastic! Will test it out on Saturday, but only a shallower dive.

My compass appears to be working much better in V2.99, I have not had to calibrate it at all, whereas before I had to do this every four or five dives.

Thanks Matthias, now working perfectly (well, not the left button).

Thanks, appears to have reset it successfully.

Tried magnet reboot again without success.

A known problem. One button died on mine, cannot be replaced.

heinrichsweikamp Wrote: ------------------------------------------------------- > You could also do a magnet reboot (No button > needed): > > - Attach to USB > - toggle the reboot with a magnet near the center > screw in the back > > That will reset your ON-Time counter and the > battery warning sho...

I can confirm that the countdown on the alternate screen now works correctly.

Used today on deco dive. All okay. Did not get a chance to see if the safety stop countdown on alternate screen is fixed. Will do this tomorrow.