forum.heinrichsweikamp.com

Sorry if it's bad form to use this forum to ask about another piece of software but I couldn't think of anywhere more appropriate.

Is anyone else using OSCT Planner at the moment? Are you having any problems? I have recently installed it onto a Mac and have updated the OSTC 2N firmware to 3.00 without any problem. However, when I try to upload the CF's I get an error message.It appears to have uploaded CF1 but stalls on `CF2 and gives the error message. The OSTC however flashes up with the warning message to say the CF;s have been changed and to check them.

Any thoughts anyone?

Regards

Jerry

use this version
https://ostc-planner.net/wp/beta-2-90-5-goes-public/

Thanks, I'll give that one a try in the morning.

Bardass Wrote:
-------------------------------------------------------
> use this version
> https://ostc-planner.net/wp/beta-2-90-5-goes-publi
> c/

That worked a treat. Thanks.

and Bardass' recommendation helped me as well!!

Thanks

Walter

Belgium

Guys,

Sorry to resurrect such an old subject but I've come across another issue. The last time I updated my firmware was when I posted this. So initially I was able to upload the firmware but had problems reading / updating the CF's. I uploaded the version suggested and had no problems with the CF's. At that point I didn't recheck the firmware updates.

Now I have decided to move to 3.13 and attempted to update via OSTC Planner. I keep getting a message that it can't locate the chip ( or something similar). The OSTC shows Bootloader in red on the screen and then changes to Bootloader aborted. I can however do a screen dump and update the time and date.

I gave up and downloaded subsurface. That worked without issue.

Any thoughts?

Jerry.

Smiler1968 Wrote:
-------------------------------------------------------
> Guys,
>
> Sorry to resurrect such an old subject but I've
> come across another issue. The last time I updated
> my firmware was when I posted this. So initially I
> was able to upload the firmware but had problems
> reading / updating the CF's. I uploaded the
> version suggested and had no problems with the
> CF's. At that point I didn't recheck the firmware
> updates.
>
> Now I have decided to move to 3.13 and attempted
> to update via OSTC Planner. I keep getting a
> message that it can't locate the chip ( or
> something similar). The OSTC shows Bootloader in
> red on the screen and then changes to Bootloader
> aborted. I can however do a screen dump and update
> the time and date.
>
> I gave up and downloaded subsurface. That worked
> without issue.
>
> Any thoughts?
>
> Jerry.

Ok has anyone on here updated firmware on a Mac using OSTC Planner recently? Did you have any issues. Am I right in thinking it can't be a driver issue as it is recognized as a com port and I can update CFs and screen dump. Would subsurface use the same drivers?

Any pointers would be appreciated. I have emailed OSTC Planner support but not heard anything back.

Regards.

i used Ostc companion with my mac

https://ostc-planner.net/wp/companion/

Can you use companion to update firmware on an OSTC2n?

yes

Bardass Wrote:
-------------------------------------------------------
> yes


OK I have just got home from work and have loaded OSTC Companion onto the Mac. The OSTC2n is recognised and I can change the name and date/time. However the Update firmware and set icon buttons are greyed out.....am I doing something wrong?

Jerry

You could always use Subsurface to both change settings and update the firmware.

Subsurface doesn't support changing all the settings on the OSTC, Mk.2/2N/2C , because they are so darn many, but the ones I have felt the need for is there.

//Anton

glance Wrote:
-------------------------------------------------------
> You could always use Subsurface to both change
> settings and update the firmware.
>
> Subsurface doesn't support changing all the
> settings on the OSTC, Mk.2/2N/2C , because they
> are so darn many, but the ones I have felt the
> need for is there.
>
> //Anton

I know I could and that is what I am doing at the moment. However the OSTC Planner was a one stop shop for everything I needed - and I supported the software by registering. It's frustrating that I can't get it to work.

As I said I think I'm right in that it's not the FTDI driver as it works with subsurface and I can screen print, adjust date and time and play around with the CF settings with Planner.

Cant get mine to work either... Cant download CF`s.. Ceeps getting error message:Bad setpoint ppO2 = 0.4[bar]
Its on a MAC too.

Edit..
Just tried it on a winblows machine and it is the same problem..
I really miss a program too edit my custom functions. Is there any other program to do this, other than ostc planner?

Diving Log can edit the custom functions.

[img]http://www.divinglog.de/blog/wp-content/2015/09/OSTCSettings-300x207.png[/img]

anybady knew why edit CF is ok ,but Uploading OSTC configuration is failed?

Thats only for winblows...

I have this on the right side of OSTC Planner 2.90.5

QSslSocket: cannot resolve TLSv1_1_client_method
QSslSocket: cannot resolve TLSv1_2_client_method
QSslSocket: cannot resolve TLSv1_1_server_method
QSslSocket: cannot resolve TLSv1_2_server_method


what is it about?