hwOS4: New Firmware 1.5.3 with RTE 2.03
Posted: Thursday 27. February 2020, 09:00
ENGLISH below.
Hallo,
Die neue Firmware 1.5.3 ist nun veröffentlicht.
heinrichsweikamp.com
Anleitung zur Installation: viewtopic.php?f=7&t=19186 (Je nach aktueller Version kann es nötig sein, das Update zweimal zu starten. Der OSTC4 gibt dazu nach dem Update nötigenfalls eine Meldung aus. Grund ist, dass möglicherweise auch sehr alte Teile der Firmware wie der Schriftsatz und der Bootloader aktualisiert werden.)
Wegen aktuell noch nicht ganz geklärten Problemen mit der iOS App OSTConf empfehlen wir, das Update mit dem OSTC Companion auf einem MAC oder Windows PC einzuspielen.
Folgende Änderungen und Neuerungen gibt es seit der V 1.4.8:
[1.5.3] with RTE 2.03
CHG: Always show battery voltage in surface mode
CHG: battery status is now preserved for future updates
NEW: Support for much faster updates (With OSTC companion 3.2 and later)
FIX: (very) short screen lag removed during sample storage in dive mode
[1.5.2] with RTE 2.02
Beta Version!
FIX: display of time of minimum voltage
FIX: Display of Sensor values. At divestart sensor values were shown even sensors were deactivated (fix SP)
FIX: Bugfix invalid voltage / temperature after coldstart
FIX: Instant dive start at several meters out of sleep mode (Jumping into the water) may resulted in lagged/freeze depth reading
CHG: Speed increase of Bluetooth communications
CHG: Look and Feel for Gauge/Apnea mode with flipped screen improved
FIX: Deco warning after Gauge mode
FIX: Download issues of corrupted dives
FIX: Proper logbook write (Very spurious error, mainly in CCR mode)
[1.5.1] with RTE 2.01
NEW: Support for end-2019 hardware
[1.5.1] with RTE 2.00
FIX: 1.5.0 could enter dive mode when ambient pressure reduced during flight
[1.5.0] with RTE 1.90
FIX: Optical port timeout fixed
FIX: firmware version in logbook data
FIX: battery information in logbook data
FIX: correct main version number logbook data
FIX: fix drawing of CCR bailout profile in internal logbook
ENGLISH:
Hello,
The new firmware 1.5.3 is now public.
heinrichsweikamp.com
Manual on how to install: viewtopic.php?f=7&t=19186
(Depending on your current version it may be required to start the update twice. The OSTC4 will show you a message after the update if this is required. Reason is, that this update also may update some older parts of the firmware like the font table and the bootloader).
Because of currently existing issues with the iOS App OSTConf we recommend to install the upgrade with the OSTC Companion on a MAC or Windows PC.
The following changes have been made since V 1.4.8:
[1.5.3] with RTE 2.03
CHG: Always show battery voltage in surface mode
CHG: battery status is now preserved for future updates
NEW: Support for much faster updates (With OSTC companion 3.2 and later)
FIX: (very) short screen lag removed during sample storage in dive mode
[1.5.2] with RTE 2.02
Beta Version!
FIX: display of time of minimum voltage
FIX: Display of Sensor values. At divestart sensor values were shown even sensors were deactivated (fix SP)
FIX: Bugfix invalid voltage / temperature after coldstart
FIX: Instant dive start at several meters out of sleep mode (Jumping into the water) may resulted in lagged/freeze depth reading
CHG: Speed increase of Bluetooth communications
CHG: Look and Feel for Gauge/Apnea mode with flipped screen improved
FIX: Deco warning after Gauge mode
FIX: Download issues of corrupted dives
FIX: Proper logbook write (Very spurious error, mainly in CCR mode)
[1.5.1] with RTE 2.01
NEW: Support for end-2019 hardware
[1.5.1] with RTE 2.00
FIX: 1.5.0 could enter dive mode when ambient pressure reduced during flight
[1.5.0] with RTE 1.90
FIX: Optical port timeout fixed
FIX: firmware version in logbook data
FIX: battery information in logbook data
FIX: correct main version number logbook data
FIX: fix drawing of CCR bailout profile in internal logbook
Hallo,
Die neue Firmware 1.5.3 ist nun veröffentlicht.
heinrichsweikamp.com
Anleitung zur Installation: viewtopic.php?f=7&t=19186 (Je nach aktueller Version kann es nötig sein, das Update zweimal zu starten. Der OSTC4 gibt dazu nach dem Update nötigenfalls eine Meldung aus. Grund ist, dass möglicherweise auch sehr alte Teile der Firmware wie der Schriftsatz und der Bootloader aktualisiert werden.)
Wegen aktuell noch nicht ganz geklärten Problemen mit der iOS App OSTConf empfehlen wir, das Update mit dem OSTC Companion auf einem MAC oder Windows PC einzuspielen.
Folgende Änderungen und Neuerungen gibt es seit der V 1.4.8:
[1.5.3] with RTE 2.03
CHG: Always show battery voltage in surface mode
CHG: battery status is now preserved for future updates
NEW: Support for much faster updates (With OSTC companion 3.2 and later)
FIX: (very) short screen lag removed during sample storage in dive mode
[1.5.2] with RTE 2.02
Beta Version!
FIX: display of time of minimum voltage
FIX: Display of Sensor values. At divestart sensor values were shown even sensors were deactivated (fix SP)
FIX: Bugfix invalid voltage / temperature after coldstart
FIX: Instant dive start at several meters out of sleep mode (Jumping into the water) may resulted in lagged/freeze depth reading
CHG: Speed increase of Bluetooth communications
CHG: Look and Feel for Gauge/Apnea mode with flipped screen improved
FIX: Deco warning after Gauge mode
FIX: Download issues of corrupted dives
FIX: Proper logbook write (Very spurious error, mainly in CCR mode)
[1.5.1] with RTE 2.01
NEW: Support for end-2019 hardware
[1.5.1] with RTE 2.00
FIX: 1.5.0 could enter dive mode when ambient pressure reduced during flight
[1.5.0] with RTE 1.90
FIX: Optical port timeout fixed
FIX: firmware version in logbook data
FIX: battery information in logbook data
FIX: correct main version number logbook data
FIX: fix drawing of CCR bailout profile in internal logbook
ENGLISH:
Hello,
The new firmware 1.5.3 is now public.
heinrichsweikamp.com
Manual on how to install: viewtopic.php?f=7&t=19186
(Depending on your current version it may be required to start the update twice. The OSTC4 will show you a message after the update if this is required. Reason is, that this update also may update some older parts of the firmware like the font table and the bootloader).
Because of currently existing issues with the iOS App OSTConf we recommend to install the upgrade with the OSTC Companion on a MAC or Windows PC.
The following changes have been made since V 1.4.8:
[1.5.3] with RTE 2.03
CHG: Always show battery voltage in surface mode
CHG: battery status is now preserved for future updates
NEW: Support for much faster updates (With OSTC companion 3.2 and later)
FIX: (very) short screen lag removed during sample storage in dive mode
[1.5.2] with RTE 2.02
Beta Version!
FIX: display of time of minimum voltage
FIX: Display of Sensor values. At divestart sensor values were shown even sensors were deactivated (fix SP)
FIX: Bugfix invalid voltage / temperature after coldstart
FIX: Instant dive start at several meters out of sleep mode (Jumping into the water) may resulted in lagged/freeze depth reading
CHG: Speed increase of Bluetooth communications
CHG: Look and Feel for Gauge/Apnea mode with flipped screen improved
FIX: Deco warning after Gauge mode
FIX: Download issues of corrupted dives
FIX: Proper logbook write (Very spurious error, mainly in CCR mode)
[1.5.1] with RTE 2.01
NEW: Support for end-2019 hardware
[1.5.1] with RTE 2.00
FIX: 1.5.0 could enter dive mode when ambient pressure reduced during flight
[1.5.0] with RTE 1.90
FIX: Optical port timeout fixed
FIX: firmware version in logbook data
FIX: battery information in logbook data
FIX: correct main version number logbook data
FIX: fix drawing of CCR bailout profile in internal logbook