Hello,
The new OSTC3, cR and OSTC 2 firmware 2.08 is now available for download: http://www.heinrichsweikamp.com/?id=479&version=de (German) or http://www.heinrichsweikamp.com/?id=479&version=en (English)
The firmware itself can be set to English, Deutsch, Italiano and Français.
[2.08]
CHANGE: Logbook marker temporally disabled in internal logbook
BUGFIX: Characters with descenders were not drawn correctly in rare cases
NEW: Support for different compass chip (Internal hardware change)
CHANGE: Language fixes
Details on hwOS: http://www.heinrichsweikamp.com/?id=335
Regards,
Matthias
hwOS for OSTC3, cR and OSTC 2: 2.08 released
-
heinrichsweikamp
- Posts: 4446
- Joined: Sunday 13. May 2007, 18:07
Re: hwOS for OSTC3, cR and OSTC 2: 2.08 released
Hi Matthias
Since I have installed this new version on my OSTC2 I cannot download my new dives to Maldive.
I checked With Subsurface, it woks Ok.
I wanted to reinstall this version again and now I cannot connect wit OSTC Companion
I have a message:Port tty.OSTC10547-SPP: Not an OSTC2.
Thanks for your help
OSTC 2 S/n 10547
Since I have installed this new version on my OSTC2 I cannot download my new dives to Maldive.
I checked With Subsurface, it woks Ok.
I wanted to reinstall this version again and now I cannot connect wit OSTC Companion
I have a message:Port tty.OSTC10547-SPP: Not an OSTC2.
Thanks for your help
OSTC 2 S/n 10547
-
heinrichsweikamp
- Posts: 4446
- Joined: Sunday 13. May 2007, 18:07
Re: hwOS for OSTC3, cR and OSTC 2: 2.08 released
Hi,
2.08 (And later) require the OSTC Companion v3, which is available as a beta yet:
https://ostc-planner.net/updates/compan ... _beta6.exe (WIN)
https://ostc-planner.net/updates/compan ... _beta6.pkg (MAC)
No need to re-install the current firmware. It's protected with several mechanisms during the installation. If it installs ("Update Successful") it is installed correctly. A re-installation will change nothing here. If subsurface works, I'm pretty sure MacDive should be fine, as well. Make sure to have the latest update for MacDive installed, as well. Some changes in the firmware require the PC/MAC software up-to-date as well.
It's the only way to integrate new features in the logbook-format, for example.
regards,
Matthias
2.08 (And later) require the OSTC Companion v3, which is available as a beta yet:
https://ostc-planner.net/updates/compan ... _beta6.exe (WIN)
https://ostc-planner.net/updates/compan ... _beta6.pkg (MAC)
No need to re-install the current firmware. It's protected with several mechanisms during the installation. If it installs ("Update Successful") it is installed correctly. A re-installation will change nothing here. If subsurface works, I'm pretty sure MacDive should be fine, as well. Make sure to have the latest update for MacDive installed, as well. Some changes in the firmware require the PC/MAC software up-to-date as well.
It's the only way to integrate new features in the logbook-format, for example.
regards,
Matthias
Re: hwOS for OSTC3, cR and OSTC 2: 2.08 released
When I updated to 2.08 I had no problems
I have the latest MacDive 2.6.5
Now with Companion V3 Beta6 it recognizes my OSTC 2
But no change when trying to download new dives after a few seconds I have the message: no new dives found
Thanks for your help
I have the latest MacDive 2.6.5
Now with Companion V3 Beta6 it recognizes my OSTC 2
But no change when trying to download new dives after a few seconds I have the message: no new dives found
Thanks for your help
-
heinrichsweikamp
- Posts: 4446
- Joined: Sunday 13. May 2007, 18:07
Re: hwOS for OSTC3, cR and OSTC 2: 2.08 released
Continue here: read.php?6,16972