forum.heinrichsweikamp.com

Done !

But with a Mac...

Thanks Matthias.

The companion indicates "block timeout" after "uploading part 1 : FW v1.05.01..."

Hi,

I tried to update but impossible.

my computer keeps going from "download mode enabled" mode to a stand-by mode.

Any suggestions ?

hello, it's the same problem for me. after driving through a mountain pass at 2000m, my computer went on its own. my problem is that here I do not have a charger or magnet ... so I am doomed to find a computer. it's really not a pleasant situation knowing that my computer comes back from repair and ...

Thanks Mattias for this new stable version.

No problem for updating my 2 computers, just like you mentioned

Hi all,

No more issue with 1.3.5, I keep it

Thanks guys for your feedbacks.

I downgrade to 1.3.5 and check it tomorrow.

Hi all,

I bought my second ostc 4.

During my first dive today the display was blocked at 1.3 meters and the timer too.
After about 16 minutes the display has unlocked and the profile has almost matched my dive (it is missing a few meters deep).

Fortunately I have a second one for backup. You ...

Hi all,

My solution for an efficient charge.
You cut the back plate around the place for the coil.

With this hole, no problem.

You can also adjust the hole and the coil will stay in the right place even if it's no stable...

My second OSTC4 has the plate with the notch.

That plate brings a greater plastic thickness that makes my charger does not work properly (blinking).

I have to remove the plate (2 screws) for a correct recharge.

Can we find a more powerfull coil ?

Hi Matthias,

Here some corrections for french. Sorry for the Word Format but usefull with colors.

Two other suggestions:

- In surface mode, the interval in french is 00j 00h (instead of 00d 00h
- In Sys menu, the format's date is JJMMAA instead of DDMMYY

Many thanks.

Hi Hansjoerg,

Thanks for your Feedback. Ok for an email...

Hi all,

I noticed in the display a kind of fog. Any idea?

Hi Christian,

Just tried today. Thanks for the logbook modifications.

I noticied that the buttons sensibility is different. I put 75% instead 90% to have the same result. Any changes ?

Hi Chrisrms,

Same for me. I put the sensitivity to 75% and no more Problem.

Just try this if needed.

Hi all,

Your are right Gorgio it's not symetric as you can see in the picture. The design I made works fine with my computer.

Here is the STL file. I do not take any garantee about the result.

Hi all,

A solution for the position's charger. I made a pad with a 3D Printer.

Hi Christian,

(tu) (tu) (tu)

Hi all,

In french version, the date format in the logbook still remains in english format (YYYY-MM-DD). In the main page (list) it's ok (DD-MM).

Could you please fix this in the next update ?


An other issue : The italien version dissapear. Only choise between french, english and german... Any ...

Hi all,

Some computer use the EN 13319 norm for the salinity which is the european standard. The value is 1020 g/dm3 as you said Laurie-the-Knot.

Thank you for this new version.

Just a request. Is it possible to change in the main display (in french version) "Air" with "Temp" ?
When we are underwater this text is more realistic.

Best regards.

Claude

Dear all,

I have the answer from HW. They have changed the size of caps and for sure I have the old one...

HW will send the new one !

Great service !

Regards.

Claude

Thanks for your comments.

I will contact HW.

Regards.

Claude

Hi you all,

I have recently purchased two OSTC 2n and for both of them water comes in through the screw cap. It seems like the screw cap can't go enough deep and is blocked by the USB connector. I can see marks on it.

Any idea ?

Fortunately it's fresh water...

Thanks for comments