New 3.13 Firmware

[heinrichsweikamp]

Hello,

Today, we released the 3.13 stable for the OSTC2 Series (2N/Mk.2/2C).

Changes since 3.00 (Changes since 3.11):
NEW: Logbook shows markers with small orange boxes in the profile
BUGFIX: Minor layout fix (Battery warning in divemode)
CHANGE: Color-code battery % display in surface mode (Charge, Full, Normal)
BUGFIX: "First Diluent" and "SP Mode" used same EEPROM location
NEW: Quit Simulator automatically when starting a real dive
CHANGE: Battery percent based on ON-Time instead of battery voltage
BUGFIX: Fix licence in German
BUGFIX: Fix minor layout bugs in surface mode
NEW: Auto Setpoint switch function (CC Modes)
BUGFIX: 1st line in logbook was not displayed in rare cases (2C hardware)
BUGFIX: Divetime had unwanted "." behind the minutes
BUGFIX: Entry time in logbook when dive was around midnight
BUGFIX: Show manually set O2 (Gas 6) correctly
BUGFIX: Show dives with >999mins divetime correctly
BUGFIX: Fix color codes 192-223 (Mk.2 and 2N only)

Updating is very easy if you have 1.90 or later and using Windows.
1. Get new bootloader v2: http://heinrichsweikamp.com/service/software
2. Follow the step-by-step instructions: http://www.heinrichsweikamp.com/?id=117&version=en


Hallo,

Heute haben wir die Version 3.13 stable für die OSTC2 Serie (2N/Mk.2/2C) veröffentlicht.

Das Updaten auf die neue Version ist sehr einfach, wenn bereits 1.90 oder später installiert ist und Windows verwendet wird.

1. Neuen bootloader v2 herunterladen: http://heinrichsweikamp.com/service/software
2. Die einfache Schritt-für-Schritt Anleitung befolgen: http://www.heinrichsweikamp.com/?id=117&version=de


Viele Grüße/Best Regards,
Matthias

[scubatinoo]

Vielen Dank euch! (tu)

[Clownfish]

Upgraded. Make sure you fully charge computer after upgrade as it resets the battery to 100%.

[Dahab Boris]

Thanks for your continued support

-D

[PAOLO]

Thanks for your continued support !!!

(tu):)-D

Cheers,

Paolo

[WG]

I gave it a couple of tries, but always get following error message when I try to start the process:

HeinrichsWeikamp Bootloader v2
www.heinrichsweikamp.com
Support: info@heinrichsweikamp.com
--------------------------------------------------------------------------------------------------
Looking for http://www.heinrichsweikamp.net/autofirmware/ostc2.hex
Could not access site information
Looking for http://www.heinrichsweikamp.net/autofirmware/ostc2.hex
Could not access site information
Looking for http://www.heinrichsweikamp.net/autofirmware/ostc2.hex
Could not access site information

Connected to \\.\COM4 at 115200
Searching for PIC ...
Found:18F 4685
Looking for http://www.heinrichsweikamp.net/autofirmware/ostc2.hex
Could not access site information

what should I do differently?

Thanks
Walter
OSTC 2531

[WG]

fixed, tried it on another computer. All OK now. Thanks for your support

Cheers

Walter

[heinrichsweikamp]

Hi Walter,

Even if you have solved this, the error indicates that the bootloader can not connect to our website. Maybe it was blocked from a firewall on the PC? Or, you did not had an active internet connection at this time.

regards,
Matthias

[Crickers]

Hi,

Have just upgraded my 2N to 3.13, have there been any updates to the custom functions?

The latest CF list I can find is v2.94

Thanks

Nick

[buk@nero]

Hi,

I have the same doubt. Are there new Custom functions, or do the ones for 2.94 apply?

Thanks for the update.

Crickers Wrote:
-------------------------------------------------------
> Hi,
>
> Have just upgraded my 2N to 3.13, have there been
> any updates to the custom functions?
>
> The latest CF list I can find is v2.94
> Thanks
>
> Nick

[Clownfish]

No changes as far as I can see.

[Laurie_the_Knot]

The only change to Custom Function that I can see is in the implementation of CF31. Before V3.12 it showed battery voltage. At V3.12 and after it shows battery percentage (%). This represents the percentage of "on" time based on the setting of CF74.

[Lee Chenyu]

hi!guys,after update, the battery bar shows low(green ,not red )and blinking.
need to wait until the battery bar shows 100% ?

[heinrichsweikamp]

It's the second thread from the top (Marked: "FAQ: Battery blinking"...)

read.php?2,16518

[Lee Chenyu]

(:P) thanks

[awanadive]

Laurie_the_Knot Wrote:
-------------------------------------------------------
> The only change to Custom Function that I can see
> is in the implementation of CF31. Before V3.12 it
> showed battery voltage. At V3.12 and after it
> shows battery percentage (%). This represents the
> percentage of "on" time based on the setting of
> CF74.

Hello, I was unable to find my answer: is it still possible with fw 3.13 to show the battery voltage?
Thank you!
AwanaDive

[Theis Thorup]

Hey Guys
Since updating to 3.13 my watch is running very fast? gaining 20 mins in a month or so?

Best,
Theis

[edhowarth]

Have a look at custom function CF48: Time offset/day

This Custom Function will correct the internal clock. The Value represents a number of seconds that will
be added to the clock at midnight.
Default value: 0:00s
Suggested range: -2:00s...+2:00s

[Theis Thorup]

Thank you but I imagine that would give an immediate offset and not add something like 30 secs a day?

[edhowarth]

No. It adds each day. At midnight.
I don't know what the maximum seconds it will do each day, but it'll be easy enough to test

[Laurie_the_Knot]

At midnight each day the software will decrement the clock by up to 120 seconds or increment it by 120 seconds.

Unfortunately there is a bug in the code which causes any attempt to increment by more than 59 seconds to decrement the clock.

So the practical range is -120 seconds (2:00 mins) to +59 seconds.

[Frank D]

Hi!

Where can I download this version's custom functions list ?

Frank (OSTC2N #4020)

[jozzbee]

Has there been any response on Frank's request?
I'm struggling too, finding the list of v3.13 C/F

[heinrichsweikamp]

Hi,

The link is in the 2nd thread in this forum called " OSTC2 Custom Functions documentation": https://forum.heinrichsweikamp.com/read.php?2,8503

https://www.angermayr.eu/index.php/de/s ... s-download

Since the 2.94 BETA, no new CFs were added. So the docsument is still valid.

Regards,
Matthias

[Isdahl]

Hi

Im using an older OSTC 2N with firmware V2.02

Im just wondering if it straight forward to do a update to firmware V3.13

And if there is a step by step guide..

Seems that it can be tricky ?? And problem with USB drivers ??


Regards,
Petter