forum.heinrichsweikamp.com

Okay, here is an update.

After reverting back to an older firmware and then reinstalling the 2,70 i have seen no problems with the NDL:s in three dives.

I still wonder what went wrong but it seems like the problem is solved.

I support this! Excellent suggestion :)

Only I would like:

=> Logbook
=> Gas Setup (renamed as "OC gas Setup"?)
=> CCR Setup (including Diluent and Set Points setup)
=> Setup (Decotype and Custom Functions)
=> More:
====> Simulator
====> Set Time
====> Battery Info
====> Altimeter ...

I updated my earlier post as i was wrong. I compared against iDeco but with a SP of 0.7 and thougt 11 minutes was right Sorry about that! I am doing too many things at once it seems.

Now it is better so please read above again

Okay, now we are getting somewhere! :)

I pushed the old 2.65 beta on and ran the same sim. This time my initial NDL was 7 minutes as opposed to showing 20min and after 7 min dropping to zero. It was also better than what I got after doing a complete reset or change the algorithms back and forth ...

heinrichsweikamp Wrote:
-------------------------------------------------------
> FTTS always shows TTS. Even during the NDL phase
> (10m/min+1min between 3 and zero), rounded up to
> the next full minute.
>
> Regards,
> Matthias

Yep, that is what i thougt. Thanks for verifying! :)

But what can ...

Are you sure the FTTS was showing NDL?

As I understand it FTTS never shows NDL and if there is no deco even if you stay the extra minutes it just shows how long it would take to ascend given the preset ascent speed. For a 33m dive it would always show 4min until it actually came in to deco.

I have ...

Second Dive

Filename: 00833_08-08-2013_054m_160min
DiveFileversion: 100
LogBookProfileVersion: 33

DiveNumber: 833
Date of dive: 2013-08-08
Time at begin of dive: 19:14:00
Time at end of dive: 21:55:00
Maximum depth (mbar): 5393
Maximum depth (bar): 5,393
Divetime: 160min 52sec

Selected Gas at ...

I have @+10 TTS activated in the background but I have Cave Bail showing on my display.

I reset the computer as you suggested and after that it showed accurate NDL:s during simulation. However during real dives it still gives strange NDL:s.

I will post the most important part of my profiles as ...

scubatinoo Wrote:
-------------------------------------------------------
>
> If it is a bug, then it affects only CC-Dives,
> not
> OC-Dives! I did some dives with 2.70 and 2.71beta
> without any problems! My OSTC everytime went
> earlier
> into Deco-Mode than my Galileo... So everything
> was ...

heinrichsweikamp Wrote:
-------------------------------------------------------
> "First" SP properly set in the "CCR Setup" Menu?
> When updating from a beta version between 2.50 and
> 2.70 the setting of the "first" SP was not
> transferred properly. Look here:
> http://forum.heinrichsweikamp.com ...

Why it was like that on the bottom i cannot answer, i had some strange deco calculations too with the new firmware. It seemed to resolve itself with a total reset and then uploading the same settings again.

However the TTS@5 should be shorter than the TTS during the deco. By how much is dependent ...

2.65 beta

Then there were no problems. Just all gasses logged wrong, thinking i was breathing air, but the NDL and deco was fine.

Hm, I reset as you suggested and then uploaded a previously saved configuration file with OSTC tools. The same config file i used to set it up when i got all the errors.
Simulation now shows proper NDL:s.

Why wrong the first time and then correct the next?

heinrichsweikamp Wrote:
-------------------------------------------------------
> Hi,
>
> My guess is that your start Diluent was not set
> (There must be a * behind it).
>
> I'd recommend to reset the Gases and CFs using the
> reset menu and setup your CCR configuration from
> scratch.
>
> It ...

Dubble post

heinrichsweikamp Wrote:
-------------------------------------------------------
> Hi,
>
> I'm not surprised the NDL drops to zero when
> switching to a setpoint of 0,5 (an OC mix of
> 10/62) in 38m. Switching back to 1.30 should give
> you the initial NDL after some minutes, of course.
> I'll have ...

Thanks, didn't know you could do that.
I cut out the interesting 10 minutes and highlighted the wierd NDL:s

120 10:00 29,26m 2869 , Temperature 36, Non Deko Limit 83min, Gradient factor 0, ppO2 Sensor Value 0, Deco Debug , CNS 1
121 10:05 29,65m 2908
122 10:10 30,11m 2953
123 10:15 30,41m 2982
124 ...

I attached a screendump from Diving log too.
You can se at min 17 where i change the setpoint down to 0.5 again the NDL drops suddenly down from around 40min to 0min.

[img]file.php?2,file=408,filename=OSTC+strange+NDL.jpg[/img]

I did my first dive with firmware version 2.70 yesterday. CCR, GF 30/90 with Tx12/62 as diluent.

Started dive with SP 0,5 and switched to 1,3 at about 25m and 10 minutes into the dive. 5 minutes later I descended to 35m and saw I had an impossible NDL of 46 minutes. For reference the Shearwater ...

Okay, I´ll se what i can do. :)

1. I do not understand what is not working. The counter does not have to do anything on the way back, it´s when and if i go back in that it has to start counting upwards again. Preferably from stored gasdata but from zero works as well if one do the math.

2 ...

If you are an OC diver DO NOT USE IT, you have gauges that show you the pressure and they are way more exact than any assumptions the bailcounter can give you.

If you are a CCR diver you put in 100% of the bailoutgas you think you will recuire in an event of an emergency. This means at least 1,5 x ...

Haha, good to know!;)

I actually use the stopwatch to show me different average depths and different timeintervals between specific distances in the cave. But i guess that is the beauty of the customview, the information can be used in many ways and a function that is useless for one person can be ...

NO!

It is not integrated with the decompresion calculator. All it does is multiply Average depth x Time x SAC.

If you want to use it for decompressiondives you have to plan how long stops you are going to make and how much gas you will need when doing them.

Hi!

After some intensive testing of the Bailout counter i am really satisfied! It is very helpful for the kind of diving that i do.

The only downside is i am starting to miss this waypoint functionality more and more for every dive. The ability to store and start gasdata from a fixed point in the ...

I have a suggestion about how to improve the custom view area.

I really like the function and that so much information can be shown there. The thing i miss, however, is the possibility to choose what information. Some of the displays can of course be turned on and off by CF:s but others are ...